Pigment Printing Problems: Poor Rubbing Fastness, Stiff Hand Feel, Uneven Colour and Curing Issues

A Complete Troubleshooting Guide for Textile and Garment Manufacturers

Pigment printing is widely used in textile and garment manufacturing because of its versatility, broad fabric compatibility and relatively simple processing requirements. However, problems such as poor rubbing fastness, stiff hand feel, uneven colour, poor print definition and incorrect curing can affect the final product.

In this guide: Understand common pigment printing defects, identify their possible causes and learn practical troubleshooting and quality-control methods.

1. What Is Pigment Printing?

Pigment printing is a textile printing process in which insoluble colour particles are applied to the fabric surface using a printing paste. Unlike conventional dyeing and printing systems that rely on dye-fibre interaction, pigment printing uses a polymer binder to hold pigment particles onto the textile surface. A typical pigment printing paste may contain:
  • Pigment dispersion: Provides the required colour.
  • Binder: Forms a film that attaches pigment particles to the fabric.
  • Thickener: Controls paste viscosity and print definition.
  • Fixer or crosslinking agent: Supports binder performance where required by the formulation.
  • Other auxiliaries: May include softeners, wetting agents and other formulation-specific additives.
Pigment printing is commonly used on cotton, polyester and blended fabrics, provided the selected formulation is suitable for the substrate.

2. Common Pigment Printing Problems

Common pigment printing defects include:
  • Poor dry rubbing fastness.
  • Poor wet rubbing fastness.
  • Stiff or harsh fabric hand feel.
  • Uneven colour and patchy appearance.
  • Poor print definition and blurred edges.
  • Low colour yield or dull shades.
  • Binder-related adhesion problems.
  • Incorrect curing or incomplete binder film formation.
  • Yellowing or shade change after curing.
  • Cracking or reduced print flexibility.

3. Poor Rubbing Fastness: Why Does Pigment Rub Off?

Poor rubbing fastness occurs when pigment colour transfers from the printed fabric to another surface during rubbing. This may happen under dry or wet conditions. Because pigment particles are held on the fabric by a binder film, rubbing performance depends on the quality and amount of binder, pigment concentration, formulation compatibility and curing conditions. Possible causes:
  • Insufficient binder in the printing paste.
  • Incorrect binder selection for the fabric or pigment system.
  • Inadequate curing or incomplete binder film formation.
  • Excessive pigment concentration compared with the binder system.
  • Incorrect fixer or crosslinker compatibility.
  • Unsuitable paste formulation or mixing conditions.
  • Fabric surface contamination or incompatible finishing.
Recommended corrective actions:
  1. Review the binder type and quantity against the chemical supplier’s recommended formulation.
  2. Check whether the pigment concentration is suitable for the binder system.
  3. Verify the curing conditions using the actual fabric temperature and required dwell time.
  4. Confirm that the fixer or crosslinker is compatible with the selected binder.
  5. Check the print paste preparation and mixing procedure.
  6. Conduct dry and wet rubbing tests on the finished printed fabric.
  7. Compare test results with the approved sample and buyer requirements.
Important Quality Note

Adding more binder is not always the correct solution. Excessive binder may improve certain fastness properties but can make the printed fabric stiff. The binder and pigment balance must be optimised.

4. Stiff Hand Feel: Why Does the Printed Fabric Become Hard?

A stiff or harsh hand feel is one of the common disadvantages associated with pigment printing. It may become more noticeable in large printed areas, heavy deposits and dark shades. Possible causes:
  • Excessive binder concentration.
  • High pigment or total paste add-on.
  • Unsuitable binder chemistry.
  • Incorrect thickener selection or paste viscosity.
  • Excessive deposition of printing paste.
  • Unsuitable softener or auxiliary compatibility.
  • Incorrect drying and curing conditions.
How to improve fabric hand feel:
  1. Review the binder level and optimise it according to the required fastness and handle.
  2. Check whether a softer binder grade is suitable for the application.
  3. Optimise paste viscosity and printing deposit.
  4. Avoid unnecessary pigment and paste loading.
  5. Evaluate compatible softeners only after checking their effect on fastness and binder performance.
  6. Compare the printed fabric handle with the approved standard.
  7. Conduct rubbing and washing tests after any formulation change.
Production Tip

The objective is not simply to make the print softer. It is to achieve an acceptable balance between soft hand feel, colour strength, adhesion and durability.

5. Uneven Colour and Patchy Printing

Uneven colour occurs when the printed design shows inconsistent shade, density or coverage across the fabric. Possible causes:
  • Inconsistent print paste viscosity.
  • Uneven pigment dispersion.
  • Unstable binder or auxiliary compatibility.
  • Uneven screen or printing pressure.
  • Fabric absorbency or surface variation.
  • Inconsistent paste application.
  • Incorrect drying conditions.
  • Variation in pigment or chemical batches.
Recommended solutions:
  1. Check paste preparation and mixing consistency.
  2. Inspect pigment dispersion for visible agglomeration or instability.
  3. Monitor paste viscosity throughout production.
  4. Check screen condition, squeegee condition and printing pressure.
  5. Inspect the fabric for surface variation and contamination.
  6. Maintain consistent drying and curing conditions.
  7. Compare the first production sample with the approved shade standard.

6. Poor Print Definition and Blurred Edges

Poor print definition occurs when the printed design does not maintain sharp outlines, fine details or the intended pattern dimensions. Possible causes:
  • Incorrect print paste viscosity.
  • Unsuitable thickener selection.
  • Excessive paste flow or spreading.
  • Damaged or unsuitable printing screen.
  • Incorrect squeegee pressure or printing conditions.
  • Fabric movement during printing.
  • Unstable pigment paste.
Corrective actions:
  • Check paste viscosity and rheological behaviour.
  • Confirm thickener compatibility with the pigment and binder system.
  • Inspect screen mesh and stencil condition.
  • Check squeegee condition and printing pressure.
  • Ensure fabric stability and correct alignment.
  • Approve a test print before bulk production.

7. Low Colour Yield and Dull Shades

Low colour yield means the printed shade appears weaker or duller than the approved target. Possible causes:
  • Unsuitable pigment selection.
  • Incorrect pigment concentration.
  • Inadequate pigment dispersion.
  • Incorrect binder and pigment compatibility.
  • Unsuitable paste viscosity.
  • Excessive penetration into the fabric.
  • Fabric colour or surface characteristics.
  • Incorrect colour measurement or viewing conditions.
Recommended solutions:
  1. Check the pigment grade and shade strength.
  2. Verify the pigment dispersion and paste stability.
  3. Review the formulation against the chemical supplier’s recommendations.
  4. Check paste viscosity and printing deposit.
  5. Evaluate the fabric before printing.
  6. Use a consistent physical colour standard for shade approval.
  7. Confirm the result after the complete drying and curing process.

8. Curing Problems: Under-Curing and Over-Curing

Curing is an important stage in pigment printing because the binder must form a suitable film to hold the pigment particles on the fabric. Incorrect curing may cause poor rubbing fastness, washing failure, excessive stiffness, yellowing or fabric damage.

Under-Curing

Under-curing occurs when the binder does not receive the required curing conditions to develop its intended performance. Possible effects:
  • Poor dry and wet rubbing fastness.
  • Poor washing durability.
  • Weak pigment adhesion.
  • Colour transfer during handling.
Checks:
  • Verify actual fabric temperature rather than relying only on the oven set-point.
  • Check dwell time and production speed.
  • Inspect airflow and temperature uniformity.
  • Confirm that the selected binder is suitable for the curing equipment.
  • Conduct fastness testing after curing.

Over-Curing

Over-curing or excessive heat exposure may affect fabric appearance, handle and shade. Possible effects:
  • Yellowing or shade change.
  • Harsh or stiff hand feel.
  • Damage to heat-sensitive fabrics.
  • Unwanted changes in fabric appearance.
Checks:
  • Review the binder supplier’s recommended curing window.
  • Check actual fabric temperature and exposure time.
  • Inspect the fabric after curing.
  • Compare the finished shade and hand feel with the approved sample.
Technical Reminder

There is no single curing temperature and time suitable for every pigment printing formulation. Binder chemistry, fabric type, paste composition and equipment all influence the required conditions. Always follow the current technical data sheet (TDS).

9. Binder Compatibility and Formulation Balance

The binder is one of the most important components in pigment printing. It holds pigment particles on the fabric and strongly influences rubbing fastness, washing performance and fabric handle. A suitable formulation must balance:
  • Colour strength and shade appearance.
  • Dry and wet rubbing fastness.
  • Washing durability.
  • Softness and fabric flexibility.
  • Print definition and surface appearance.
  • Compatibility with other auxiliaries.
Good formulation practices:
  1. Use a binder recommended for the intended fabric and pigment system.
  2. Check compatibility before mixing different chemical products.
  3. Follow the supplier’s recommended mixing sequence.
  4. Maintain controlled paste preparation and storage.
  5. Evaluate the final print after complete curing.
  6. Record approved recipes and test results.

10. Pigment Printing Troubleshooting Chart

Defect Possible Cause Recommended Check
Poor dry rubbing fastness Insufficient binder or unsuitable curing Binder formulation and curing validation
Poor wet rubbing fastness Binder performance or formulation issue Binder and fixer compatibility
Stiff hand feel Excessive binder or paste deposit Binder level and print add-on
Uneven colour Paste instability or inconsistent printing Viscosity, dispersion and screen condition
Blurred edges Unsuitable viscosity or excessive paste flow Thickener and printing conditions
Low colour yield Pigment selection or dispersion issue Pigment grade and paste formulation
Yellowing Binder chemistry or excessive heat exposure Binder specification and curing conditions
Poor washing durability Insufficient binder film formation Curing process and wash test

11. Quality Control Checklist Before Bulk Production

  • ☐ Confirm fabric composition and surface condition.
  • ☐ Verify pigment and binder compatibility.
  • ☐ Check pigment dispersion and paste stability.
  • ☐ Verify print paste viscosity.
  • ☐ Inspect screen and squeegee condition.
  • ☐ Approve the initial printed sample.
  • ☐ Check colour strength and shade consistency.
  • ☐ Evaluate fabric hand feel.
  • ☐ Verify actual curing conditions.
  • ☐ Conduct dry rubbing fastness testing.
  • ☐ Conduct wet rubbing fastness testing.
  • ☐ Conduct washing fastness testing where required.
  • ☐ Compare results with buyer specifications.
  • ☐ Record approved formulation and process conditions.

12. Best Practices for Consistent Pigment Printing Quality

Choose the correct binder: Select a binder that meets the required fastness and fabric handle specifications. Control pigment concentration: Avoid excessive pigment loading that may affect binder performance. Maintain paste consistency: Monitor viscosity, dispersion and stability throughout production. Control printing deposit: Use suitable screen and printing conditions to achieve the required coverage without unnecessary paste application. Validate curing: Confirm actual fabric temperature and dwell time using the supplier’s technical instructions. Test before bulk production: Evaluate rubbing fastness, washing durability, shade and hand feel on the actual fabric. Maintain records: Keep approved formulations, chemical batch details, curing records and quality test reports.

13. Frequently Asked Questions (FAQ)

Q1. Why does pigment print rub off from fabric?

Poor rubbing fastness may result from insufficient binder, unsuitable binder selection, excessive pigment concentration or inadequate curing. Check the complete formulation and test the finished print.

Q2. Why does pigment printing make fabric stiff?

Excessive binder, high paste deposit and unsuitable formulation can create a thicker or harder film on the fabric surface, resulting in a stiff hand feel.

Q3. How can wet rubbing fastness be improved?

Review the binder system, fixer compatibility and curing conditions. Confirm the improvement through a suitable wet rubbing fastness test rather than relying only on visual inspection.

Q4. What causes uneven pigment printing?

Uneven pigment dispersion, unstable paste viscosity, fabric variation, screen condition and inconsistent printing pressure can all contribute to patchy colour.

Q5. What happens if pigment printing is under-cured?

The binder may not form a sufficiently durable film, which can lead to poor rubbing fastness, weak adhesion and reduced washing durability.

Q6. Does increasing binder always improve pigment printing?

No. Increasing binder may improve certain fastness properties, but excessive binder can make the fabric stiff. The formulation needs to balance durability and hand feel.

14. Conclusion

Pigment printing problems such as poor rubbing fastness, stiff hand feel, uneven colour and curing defects can affect the quality and performance of finished garments.

Consistent results depend on suitable binder selection, balanced pigment formulation, controlled paste viscosity, correct printing conditions and validated curing.

Balance print durability with fabric comfort, verify every formulation through testing and maintain documented process controls before bulk production.

Technical References

Technical note: Pigment printing formulations and curing requirements vary according to binder chemistry, pigment concentration, fabric composition and production equipment. Always follow the current chemical supplier’s technical data sheet (TDS), safety data sheet (SDS) and approved production procedures.

Scroll to Top